VelvetDrive Transmission |
Post Reply ![]() |
Author | |
sam57 ![]() Senior Member ![]() ![]() Joined: December-07-2007 Location: North Canton, O Status: Offline Points: 360 |
![]() ![]() ![]() ![]() ![]() Posted: June-18-2009 at 11:12pm |
VelvetDrive AS11 72C It came out of a 1966 Century with a 427 Commander with only 230 original hours. Been sitting on the shelf for 17 years, turns easy and shifts easy, and no rust. $250.
Sam |
|
![]() |
|
eric lavine ![]() Grand Poobah ![]() Joined: August-13-2006 Location: United States Status: Offline Points: 13413 |
![]() ![]() ![]() ![]() ![]() |
will work behind a small block also, a touch longer, and 5' coupling instead of 4"
Sam 10 spline input shaft, or 26? |
|
"the things you own will start to own you"
|
|
![]() |
|
sam57 ![]() Senior Member ![]() ![]() Joined: December-07-2007 Location: North Canton, O Status: Offline Points: 360 |
![]() ![]() ![]() ![]() ![]() |
Eric, 26 spline input shaft.
Sam |
|
![]() |
|
oldboat ![]() Newbie ![]() Joined: October-02-2007 Location: United States Status: Offline Points: 7 |
![]() ![]() ![]() ![]() ![]() |
Sam - I have a 57 Luger running a 400 ci Pontiac - will the velvet work on it - now using a three spd manual with a hydraulic auto clutch and I want to convert - I also need a bell housing which fits Buick/Cadillac/Oldsmobile/Pontiac - believe Chev is different. I am not that familiar with them marine drives.
I also have a 54 CorrectCraft that is on the Club site - bought new by my Dad. Thanks - Dave |
|
![]() |
|
sam57 ![]() Senior Member ![]() ![]() Joined: December-07-2007 Location: North Canton, O Status: Offline Points: 360 |
![]() ![]() ![]() ![]() ![]() |
Dave,
I don't see why my velvet drive wouldn't work. It's made for high horsepower engines. I don't have a bell housing, but I don't think they are that hard to find. Sam |
|
![]() |
|
clarkebar ![]() Senior Member ![]() Joined: January-13-2008 Location: marietta, GA Status: Offline Points: 174 |
![]() ![]() ![]() ![]() ![]() |
sam is the trans for sale?
Eric |
|
![]() |
|
sam57 ![]() Senior Member ![]() ![]() Joined: December-07-2007 Location: North Canton, O Status: Offline Points: 360 |
![]() ![]() ![]() ![]() ![]() |
Eric,
Yes, the transmission is for sale. Sam |
|
![]() |
|
clarkebar ![]() Senior Member ![]() Joined: January-13-2008 Location: marietta, GA Status: Offline Points: 174 |
![]() ![]() ![]() ![]() ![]() |
I have a A1 70C was wondering if it would work with my small block. Eric stated that it would.
|
|
![]() |
|
sam57 ![]() Senior Member ![]() ![]() Joined: December-07-2007 Location: North Canton, O Status: Offline Points: 360 |
![]() ![]() ![]() ![]() ![]() |
Eric would know!
|
|
![]() |
|
Luchog ![]() Grand Poobah ![]() ![]() Joined: April-17-2007 Location: Argentina Status: Offline Points: 2135 |
![]() ![]() ![]() ![]() ![]() |
would that be the same "Commander" company wich did the 351s? if so they were around for some 20 years!! Any other engines they did? |
|
![]() |
|
sam57 ![]() Senior Member ![]() ![]() Joined: December-07-2007 Location: North Canton, O Status: Offline Points: 360 |
![]() ![]() ![]() ![]() ![]() |
I had a 83 Correct Craft with a Commander 351, and a 66 Lyman with a 289 Commander. I don't know if they did any Chevrolet based engines or just Fords.
|
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |