Boats For Sale:
Wiring diagram |
Post Reply 
|
| Author | |
Potlatch 
Newbie 
Joined: May-09-2012 Location: Aberdeen, WA Status: Offline Points: 8 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Wiring diagramPosted: May-10-2012 at 9:53pm |
|
Where would I find a wiring diagram that shows dashboard & gauge wiring? My manual shows engine wiring, but I want to correct some of the under-dash stuff that previous owners had done. Thanks.
|
|
 |
|
|
Bri892001
Grand Poobah 
Joined: September-27-2008 Location: Boston MA Status: Offline Points: 4947 |
Post Options
Thanks(0)
Quote Reply
Posted: May-11-2012 at 12:21pm |
|
Welcome to the site,
You mentioned in your other post that it's for a 91 (It's good to keep all responses for a subject on one thread) Unfortunately the closest you're going to get for a 91, is this diagram for an 89: http://www.correctcraftfan.com/downloads/1989_SN_Wiring_Diagram.pdf There aren't major differences though. |
|
|
|
|
N2Deep
Senior Member 
Joined: April-13-2012 Location: Las Vegas Status: Offline Points: 141 |
Post Options
Thanks(0)
Quote Reply
Posted: May-11-2012 at 2:21pm |
|
I have my whole dash apart right now and can help ya with whatever your trying to do. I should be putting it back together this weekend after repairing the plastic. So let me know what you need before i get it all back in the boat.
|
|
|
1991 SN pulled by a 2010 Tundra
|
|
|
|
|
Bri892001
Grand Poobah
Joined: September-27-2008 Location: Boston MA Status: Offline Points: 4947 |
Post Options
Thanks(0)
Quote Reply
Posted: May-11-2012 at 2:30pm |
|
Craig, could you post some general pics? Especially a rear view of all the gauges and everything from behind the dash?
|
|
|
|
|
N2Deep
Senior Member
Joined: April-13-2012 Location: Las Vegas Status: Offline Points: 141 |
Post Options
Thanks(0)
Quote Reply
Posted: May-11-2012 at 3:31pm |
|
Yup will do tonight when I get home if I can get it back together tonight. Anything specific you need? I will take some with it taken apart and then a complete one when it is back together.
I used the Plastex repair kit and it worked very well - just have some sanding to do so and glue the fabric back on in a few small places. Now my dash is in really good shape and no cracks or broken pieces - just a couple crappy looking gauges that need replaced. LOL |
|
|
1991 SN pulled by a 2010 Tundra
|
|
|
|
|
N2Deep
Senior Member
Joined: April-13-2012 Location: Las Vegas Status: Offline Points: 141 |
Post Options
Thanks(0)
Quote Reply
Posted: May-11-2012 at 3:33pm |
|
I have gone through ALL the wiring in this boat so can tell you where any and every wire goes. A few late nights and lots of fun
 Just about ready to start putting her back together and get her on the water. |
|
|
1991 SN pulled by a 2010 Tundra
|
|
|
|
|
Bri892001
Grand Poobah
Joined: September-27-2008 Location: Boston MA Status: Offline Points: 4947 |
Post Options
Thanks(0)
Quote Reply
Posted: May-11-2012 at 4:05pm |
|
I'm mostly interested in the wiring. I've run a new ground and cleaned some things up on mine, but I think it's going to need a thorough run through.
|
|
|
|
|
N2Deep
Senior Member
Joined: April-13-2012 Location: Las Vegas Status: Offline Points: 141 |
Post Options
Thanks(0)
Quote Reply
Posted: May-14-2012 at 2:21pm |
|
Sorry this post got screwed up had to repost. |
|
|
1991 SN pulled by a 2010 Tundra
|
|
|
|
|
N2Deep
Senior Member
Joined: April-13-2012 Location: Las Vegas Status: Offline Points: 141 |
Post Options
Thanks(0)
Quote Reply
Posted: May-14-2012 at 2:22pm |
|
Here are some pics but not sure its gonna help ya rewire something because some of the wires are the same color that go to different gauges.
Let me know if you have any specific questions and I can try and help1991 Ski Nautique |
|
|
1991 SN pulled by a 2010 Tundra
|
|
|
|
|
Bri892001
Grand Poobah
Joined: September-27-2008 Location: Boston MA Status: Offline Points: 4947 |
Post Options
Thanks(0)
Quote Reply
Posted: May-14-2012 at 2:36pm |
|
There's more stuff than I realized going to the temp gauge...
I figured: -hot (ignition) wire -ground, -sender -lights I guess everything is daisy chained, so some of those bundles represent one connection. It still looks like a lot. Does one wire go to the alarm or something like that? |
|
|
|
|
N2Deep
Senior Member
Joined: April-13-2012 Location: Las Vegas Status: Offline Points: 141 |
Post Options
Thanks(0)
Quote Reply
Posted: May-14-2012 at 3:24pm |
|
On the Temp gauge you have your grounds and backlight. Then the browns go to the Temp sensor and the purples are power, alarm and the temp warning light.
I can trace them out for ya if you want- while I have the dash off. Its kinda hard to take pictures and trace the wires from a pic. Let me know what you want traced and I can get it done tonight. |
|
|
1991 SN pulled by a 2010 Tundra
|
|
|
|
|
Bri892001
Grand Poobah
Joined: September-27-2008 Location: Boston MA Status: Offline Points: 4947 |
Post Options
Thanks(0)
Quote Reply
Posted: May-14-2012 at 3:37pm |
|
Ok, thanks, that helps. No specific questions. I have that Faria replacement temp gauge, that I've yet to install. My old one allowed moisture in and is kind of fogged over. But, it doesn't use the same spade connectors, so it's not exactly plug n play.
|
|
|
|
|
Potlatch
Newbie
Joined: May-09-2012 Location: Aberdeen, WA Status: Offline Points: 8 |
Post Options
Thanks(0)
Quote Reply
Posted: May-14-2012 at 6:04pm |
|
Thanks all.... think I've got it figured out.
|
|
|
|
|
hoch323
Newbie
Joined: April-04-2012 Location: Wonder Lake, IL Status: Offline Points: 33 |
Post Options
Thanks(0)
Quote Reply
Posted: May-24-2012 at 3:08pm |
|
N2Deep posted some nice pictures of the wiring on the back of his gauges. Are black wires in the pictures always ground?
|
|
|
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: May-24-2012 at 3:33pm |
Dave, The black ones should be ground but you never know who's been in there messing with things. You'd better get the VOM out and check. I ALWAYS do before having a problem. |
|
|
|
|
Bri892001
Grand Poobah
Joined: September-27-2008 Location: Boston MA Status: Offline Points: 4947 |
Post Options
Thanks(0)
Quote Reply
Posted: June-06-2012 at 5:56pm |
|
Craig,
I was looking at your dash wiring pics again. I had one question about the temp gauge area: -The group of Purple wires on the gauge is the ignition daisy chain -The group of Black wires on the gauge is the ground daisy chain -The group of blue/white wires on the gauge is the lights daisy chain -The group of brown/tan wires on the gauge is the sending, right? I see another grouping of two blacks, poking in near the purple ignition. Do you know what those are for? Or is it just the pic that makes it look like they're connecting? Thanks, Brian |
|
|
|
|
N2Deep
Senior Member
Joined: April-13-2012 Location: Las Vegas Status: Offline Points: 141 |
Post Options
Thanks(0)
Quote Reply
Posted: June-06-2012 at 8:04pm |
|
The set of black that is with the set of Blue is the ground for the back lighting or gauge light. The black that is behind the purple is the ground group for the gauge.
Hope that helps |
|
|
1991 SN pulled by a 2010 Tundra
|
|
|
|
|
Bri892001
Grand Poobah
Joined: September-27-2008 Location: Boston MA Status: Offline Points: 4947 |
Post Options
Thanks(0)
Quote Reply
Posted: June-06-2012 at 8:20pm |
 Ahh, I get it now.Makes sense... well, I understand it anyway. So, the light for the gauge, is treated as it's own separate component. |
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
hoch323 wrote: