shaft collar |
Post Reply |
Author | |
The Dude
Platinum Member Joined: October-19-2004 Location: Houston Status: Offline Points: 1334 |
Post Options
Thanks(0)
Posted: March-17-2017 at 10:03pm |
does this collar with the set screws sticking out move? I can't get the nut back far enough to be able to replace packing.
|
|
Mullet Free since 93
95 Sport |
|
OldSchoolBlue84
Gold Member Joined: December-02-2012 Location: Valparaiso, IN Status: Offline Points: 814 |
Post Options
Thanks(0)
|
Yes sir, should slide, may have to work with it.
|
|
Kostas
1984 Ski Nautique 2001 |
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
|
David,
FYI, that collar is the safety collar. If the prop shaft breaks say at the trans, it prevents the shaft from moving aft. A shaft breaking at the trans is one of the problems caused by poor engine to shaft alignment. |
|
The Dude
Platinum Member Joined: October-19-2004 Location: Houston Status: Offline Points: 1334 |
Post Options
Thanks(0)
|
dang salt water.
OK. I'll "work" with it tomorrow. I watched your most excellent vid on prop alignment yesterday Pete. I've done it several times, but it's time again with everything out. It started with new fuel sender. Then rudder packing, now shaft packing and alignment. |
|
Mullet Free since 93
95 Sport |
|
Duane in Indy
Platinum Member Joined: October-26-2015 Location: Indiana Status: Offline Points: 1578 |
Post Options
Thanks(0)
|
Just got one of these off of e-bay. It is spit so you can take it on or off without removing the coupling. Also the split type will not mark the shaft. All S/S
http://i.ebayimg.com/images/g/LwwAAOSw6n5XtkIw/s-l1600.jpg |
|
Keep it as original as YOU want it
1978 Mustang (modified) |
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
|
David,
If you can't get it loose, you may need to cut the collar. I would use a cut off wheel in a die grinder (Dremmel) and cut close to the shaft. Then driving a cold chisel in the slot should open up the ID enough to free the collar. |
|
TRBenj
Grand Poobah Joined: June-29-2005 Location: NWCT Status: Offline Points: 21171 |
Post Options
Thanks(0)
|
Duane, not sure what the eBay price is but I grabbed several of the split collar stainless ones from amazon for $14 (free shipping). Cheap insurance.
|
|
Duane in Indy
Platinum Member Joined: October-26-2015 Location: Indiana Status: Offline Points: 1578 |
Post Options
Thanks(0)
|
Bout the same, $12.98 shipped BTW, My new PSS seal is arriving today, will install both |
|
Keep it as original as YOU want it
1978 Mustang (modified) |
|
The Dude
Platinum Member Joined: October-19-2004 Location: Houston Status: Offline Points: 1334 |
Post Options
Thanks(0)
|
got the collar loose
|
|
Mullet Free since 93
95 Sport |
|
Duane in Indy
Platinum Member Joined: October-26-2015 Location: Indiana Status: Offline Points: 1578 |
Post Options
Thanks(0)
|
I suggest not reinstalling it. Order the 2 piece type and install it when it arrives. Took 2 days for me to get mine. Just my $.02 |
|
Keep it as original as YOU want it
1978 Mustang (modified) |
|
swilliams
Senior Member Joined: June-26-2016 Location: Cincinnati,Ohio Status: Offline Points: 236 |
Post Options
Thanks(0)
|
Can you guys be a little more specific about the 2 piece collar(part number, etc.)? Looking to do that for mine. Didn't mean to hi-jack this! Thanks
|
|
Duane in Indy
Platinum Member Joined: October-26-2015 Location: Indiana Status: Offline Points: 1578 |
Post Options
Thanks(0)
|
This was posted above and earlier Just got one of these off of e-bay. It is spit so you can take it on or off without removing the coupling. Also the split type will not mark the shaft. All S/S http://i.ebayimg.com/images/g/LwwAAOSw6n5XtkIw/s-l1600.jpg |
|
Keep it as original as YOU want it
1978 Mustang (modified) |
|
swilliams
Senior Member Joined: June-26-2016 Location: Cincinnati,Ohio Status: Offline Points: 236 |
Post Options
Thanks(0)
|
Thanks Duane,I couldn't post the link. I'll try typing it in.
|
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
|
Here's the direct link Doesn't work for me ether! |
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
|
Duane in Indy
Platinum Member Joined: October-26-2015 Location: Indiana Status: Offline Points: 1578 |
Post Options
Thanks(0)
|
type this into search line when you are on ebay
282307507033 edit or: 1" Inch Stainless Steel Double Split Shaft Collar - 2SSC-100 |
|
Keep it as original as YOU want it
1978 Mustang (modified) |
|
swilliams
Senior Member Joined: June-26-2016 Location: Cincinnati,Ohio Status: Offline Points: 236 |
Post Options
Thanks(0)
|
Thanks!
|
|
The Dude
Platinum Member Joined: October-19-2004 Location: Houston Status: Offline Points: 1334 |
Post Options
Thanks(0)
|
I sure love this site...I reference it all the time and should post more often.
New fuel sender, repacked rudder stuffing, shaft alignment, repacked shaft seal, general clean up the bilge (pretty clean anyway). Feels so good to get it all done. Excited to get on the water this week and see how dry the bilge is. Thanks everyone. |
|
Mullet Free since 93
95 Sport |
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |