1981 SN plumbing |
Post Reply |
Author | |
MourningWood
Gold Member Joined: June-13-2014 Location: NorCal Status: Offline Points: 915 |
Post Options
Thanks(0)
Posted: March-26-2018 at 7:50pm |
As originally equipped, what dia. was water inlet hose from thru-hull to water strainer?
I have a Vetus basket type strainer with 1" in and out. I think it is original. I ask because of all the Home Depot pipe/reducers/clamps/laundry hoses/pvc/ball valves, etc. that was done before my time.... Thanks |
|
1964 Dunphy X-55 "One 'N Dun"
'I measured twice, cut three times, and it's still too short!" |
|
KENO
Grand Poobah Joined: June-06-2004 Location: United States Status: Offline Points: 11093 |
Post Options
Thanks(0)
|
An inch ID.
On a PCM 351 everything from the thru hull fitting up to the RWP is an inch. The outlet from the RWP is an inch And I think Zach mentioned in your other thread the hoses from the thermostat housing to the manifolds are .............an inch. |
|
MourningWood
Gold Member Joined: June-13-2014 Location: NorCal Status: Offline Points: 915 |
Post Options
Thanks(0)
|
I thank you.
Yes, Zach helped me with t-stat hoses. I'll buy plenty of 1". I'll get some photos up soon of the 'lightweight' 351 and the modified cooling system... Actually just brought the boat around from the barn today. Sun is out! |
|
1964 Dunphy X-55 "One 'N Dun"
'I measured twice, cut three times, and it's still too short!" |
|
KENO
Grand Poobah Joined: June-06-2004 Location: United States Status: Offline Points: 11093 |
Post Options
Thanks(0)
|
You talked about a crank driven RWP at some point in the recent past.
If you got one, does it have 1 inch connections ? Only reason I ask is because the typical crank driven pump on an Indmar 351W has 1 1/4 inch fittings. There must be a crank driven pump out there with 1 inch fittings though. |
|
MourningWood
Gold Member Joined: June-13-2014 Location: NorCal Status: Offline Points: 915 |
Post Options
Thanks(0)
|
you're right..
I had a Johnson crank rwp knocking around, am using it on my build. It is 1 1/4" both in and out. It will feed into a "gutted" circ pump (now just a manifold) and exit into a modified t-stat housing, then to exhaust. Also a couple hoses to bleed off excess rwp pressure. Actually very straightforward. just hope it works as planned... |
|
1964 Dunphy X-55 "One 'N Dun"
'I measured twice, cut three times, and it's still too short!" |
|
phatsat67
Grand Poobah Joined: March-13-2006 Location: Indiana Status: Offline Points: 6157 |
Post Options
Thanks(0)
|
12 feet is usually enough to take care of a PCM Ford in any CC boat, Maybe a little extra but it's better to be too long than too short.....
|
|
Gary S
Grand Poobah Joined: November-30-2006 Location: Illinois Status: Offline Points: 14096 |
Post Options
Thanks(0)
|
Luckily your among friends Zach,thats just too easy..........
|
|
Hollywood
Moderator Group Joined: February-04-2004 Location: Twin Lakes, WI Status: Offline Points: 13514 |
Post Options
Thanks(0)
|
He's had a lifetime of learning that
|
|
gt40KS
Gold Member Joined: August-05-2017 Location: Wichita Kansas Status: Offline Points: 946 |
Post Options
Thanks(0)
|
Well that took a hard 90
Seriously though, is it about the same for the 90's era SN? I figure 75-80% of everything else is going to be new and considering there was only a handful of hose, pipe or wire in the entire mess that hadn't been spliced at least once .... |
|
JCCI
1995 Ski Nautique GT40 |
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |