Forums
NautiqueParts.comNautiqueSkins.com - Correct Craft Upholstery and Part
  New Posts New Posts RSS Feed - Front block holes
  FAQ FAQ  Forum Search   Register Register  Login Login

Front block holes
 Post Reply Post Reply   
Author
  Topic Search Topic Search  Topic Options Topic Options
NeilMcG View Drop Down
Senior Member
Senior Member


Joined: September-20-2021
Location: Pittsburgh, PA
Status: Offline
Points: 228 		Post Options Post Options   Thanks (0) Thanks(0)   Quote NeilMcG Quote  Post ReplyReply Direct Link To This Post Topic: Front block holes
    Posted: July-28-2024 at 8:43pm
351 PCM
Does anyone know what these holes are used for? I can't think of anything missing but after looking things over I'm a bit concerned.
Back to Top
GottaSki View Drop Down
Grand Poobah
Grand Poobah


Joined: April-21-2005
Location: NE CT
Status: Offline
Points: 3363 		Post Options Post Options   Thanks (0) Thanks(0)   Quote GottaSki Quote  Post ReplyReply Direct Link To This Post Posted: July-29-2024 at 7:39am
nothing.

but, Id be more concerned with the missing tygon tube from fuel pump, to the spark arrestor/carb
"There is nothing, absolutely nothing, half so much worthwhile as messing around with boats...simply messing."

River Rat to Mole
Back to Top
TRBenj View Drop Down
Grand Poobah
Grand Poobah
Avatar

Joined: June-29-2005
Location: NWCT
Status: Offline
Points: 21186 		Post Options Post Options   Thanks (0) Thanks(0)   Quote TRBenj Quote  Post ReplyReply Direct Link To This Post Posted: July-29-2024 at 11:48am
I think that lower bolt hole is typically used by PCM to hang the water inlet hose bracket.
Back to Top
NeilMcG View Drop Down
Senior Member
Senior Member


Joined: September-20-2021
Location: Pittsburgh, PA
Status: Offline
Points: 228 		Post Options Post Options   Thanks (0) Thanks(0)   Quote NeilMcG Quote  Post ReplyReply Direct Link To This Post Posted: July-29-2024 at 12:04pm
Originally posted by GottaSki GottaSki wrote:

nothing.

but, Id be more concerned with the missing tygon tube from fuel pump, to the spark arrestor/carb
I have the sight tube, just haven't put it on yet.
Back to Top
NeilMcG View Drop Down
Senior Member
Senior Member


Joined: September-20-2021
Location: Pittsburgh, PA
Status: Offline
Points: 228 		Post Options Post Options   Thanks (0) Thanks(0)   Quote NeilMcG Quote  Post ReplyReply Direct Link To This Post Posted: July-29-2024 at 12:04pm
Originally posted by TRBenj TRBenj wrote:

I think that lower bolt hole is typically used by PCM to hang the water inlet hose bracket.

Ah ha...that's it! Thanks
Back to Top
KENO View Drop Down
Grand Poobah
Grand Poobah


Joined: June-06-2004
Location: United States
Status: Offline
Points: 11116 		Post Options Post Options   Thanks (0) Thanks(0)   Quote KENO Quote  Post ReplyReply Direct Link To This Post Posted: July-29-2024 at 1:15pm



Originally posted by TRBenj TRBenj wrote:

I think that lower bolt hole is typically used by PCM to hang the water inlet hose bracket.

Kinda like this picture from an old CCF thread shows 

Ignore the vent hose routing and maybe another thing or 2 also  Wink
 
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

About CCF

Since 2003, CorrectCraftFan.com has been the foremost Correct Craft reference site, and simply provides the best used Correct Craft buying and selling experience anywhere.

Donate

This site is not affiliated with Correct Craft, Inc. Funding for the site comes from members like you. Click on the link below to make a donation.

Partners

Contact

Keith@CorrectCraftFan.com
Alison@CorrectCraftFan.com
www.CorrectCraftFan.com
Copyright 2024 | Bagley Productions, LLC