Boats For Sale:
1964 CC Mustang Drive Shaft Bushing |
Post Reply 
|
| Author | |
Toigs325 
Groupie 
Joined: September-15-2009 Location: Minocqua, WI Status: Offline Points: 90 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: 1964 CC Mustang Drive Shaft BushingPosted: December-01-2009 at 12:41pm |
|
All,
I have a 1964 Correct Craft Mustang that is missing the bushing or assembly (not sure what to call it) that goes around the drive shaft at the hull. I am not exactly sure what the part looks like nor am I sure what it is called because it wasnt there when I bought it and I have never seen another 60s Mustang out of the water. Can anyone tell me anything about this part? What is it called? Part number? How do I find one? How do I install it? Any information would be greatly appreciated as I would really like this boat to float at some point in the near future, Thanks, Toigs325 |
|
|
2003 Ski Nautique 196 SE
1966 Correct Craft Mustang |
|
 |
|
|
Riley
Grand Poobah 
Joined: January-19-2004 Location: Portland, ME Status: Offline Points: 7953 |
Post Options
Thanks(0)
Quote Reply
Posted: December-01-2009 at 12:57pm |
|
There are 2 parts where the shaft goes through the hull. One is the stuffing box and the other is the shaft log. The shaft log is fiberglassed into the boat. The shaft log looks like a brass pipe that comes up out of the hull. The stuffing box connects to it with a piece of rubber hose. Check the shaft log to make sure it wasn't ground down by misalignment.
The stuffing box is the smaller part in the photo. 
|
|
|
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: December-01-2009 at 1:44pm |
|
Andrew,
Here's a link to Buck Algonquin for the stuffing box. Do check the log as recommended by Bruce to make sure it's not ground out inside. With all that water you have over there, you need to spend some more time with the boats. All inboards have them. 
|
|
|
|
|
Toigs325
Groupie
Joined: September-15-2009 Location: Minocqua, WI Status: Offline Points: 90 |
Post Options
Thanks(0)
Quote Reply
Posted: December-02-2009 at 12:15am |
|
Thanks for the information guys. The part that I am missing is the seal assembly that is found where the drive shaft meets the hull, I believe it is usually flush with the hull. Is that the stuffing box? There is a rectangular hole around the drive shaft that now allows water to come in. I am assuming it is not supposed to be there and that I am missing a piece. I have the part that supports the drive shaft and the rudder.
|
|
|
2003 Ski Nautique 196 SE
1966 Correct Craft Mustang |
|
|
|
|
Gary S
Grand Poobah
Joined: November-30-2006 Location: Illinois Status: Offline Points: 14096 |
Post Options
Thanks(0)
Quote Reply
Posted: December-02-2009 at 12:32am |
|
Sounds like he's missing the log don't it? If you could post a picture that would help alot.
|
|
|
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: December-02-2009 at 9:01am |
Andrew, Here's another link to Buck Algonquin stuffing box and log. Just as Bruce mentioned, the long flange on the log is glassed into the hull. |
|
|
|
|
SNobsessed
Grand Poobah
Joined: October-21-2007 Location: IA Status: Offline Points: 7102 |
Post Options
Thanks(0)
Quote Reply
Posted: December-02-2009 at 10:28am |
|
Seems to me someone else replaced the log earlier this year. That thread may help Andrew get started with his repair.
|
|
|
“Beer is proof that God loves us and wants us to be happy.”
Ben Franklin |
|
|
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: December-02-2009 at 10:59am |
Chris, You may be thinking of Andy (okie boarder). Andy was having major leak problems at the log on his Supra and had started a thread on it over on wakeboarder.com. HW asked me to take a look at it. Andy having posted pictures (he always does which is good!!!) the problem was pretty obvious. With his glassing background being very limited, I ended up walking him through the process of getting the log out and then glassing it back in. Now look at what he's doing - some of us wouldn't undertake the major stringer job on a Supra with having to pulling the cap!!! I'll see if I can link the thread. It would be a great one because it was a step by step with pictures. BTW, it sure says something about CCfan when non CC owners come to the site with problems!! We should be and I know I'm proud that we can help out. |
|
|
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: December-02-2009 at 1:08pm |
|
Andy,
Help me out with a link. I can't find your thread on the log over on wakeboarder even going through 15 pages!! BTW, it's been awhile since I visited the site and noticed you're keeping the members over there informed on you stringer job too. (You've got the majority of them amazed!!) I also noticed some of the questions the members are asking. No offence but it's apparent why some come to CCfan for tech advice!! Keep up the great work. You're going to end up with one hell of a boat that you will be very proud of. |
|
|
|
|
kapla
Grand Poobah
Joined: March-27-2008 Location: BA, Argentina Status: Offline Points: 6148 |
Post Options
Thanks(0)
Quote Reply
Posted: December-02-2009 at 1:08pm |
|
what about helping a MC owner? ....
|
|
|
<a href="">1992 ski nautique
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
Riley wrote: